A customer uploads a photo of their dog, stretches it across the whole front of a hoodie and pays. The photo was 640 pixels wide. You now have three options, all bad: print it and get a complaint, email them and wait two days for a better file, or refund.
The fix is to catch the problem while the customer is still designing, when replacing the photo takes ten seconds. This post shows how to think about it and how to set it up.
Why "the file is big" is not enough
A file's pixel count says nothing on its own. What matters is effective DPI: how many of those pixels land on each inch of the print, at the size the customer placed it.
The same 2000-pixel-wide photo is:
- about 500 DPI as a 10 cm chest logo, which is excellent;
- about 170 DPI stretched to 30 cm across the front, which is borderline;
- about 130 DPI on a 40 cm poster, which will look soft.
So the check has to run after the customer has placed and scaled the image, not when the file is uploaded. A check at upload time either rejects good files or lets bad ones through. (If the numbers are new to you, the previous post on DPI, bleed and safe zones explains them.)
Decide what happens below the line
Pick two thresholds and one behaviour.
| Setting | A sensible start | Why |
|---|---|---|
| Target resolution | 300 DPI | Above this, nobody can tell the difference. |
| Hard floor | 150 DPI | Below this, most prints look visibly soft. |
| Checkout behaviour | Warn the customer | Lets them decide, and records that they were told. |
Between the two thresholds, a warning is enough. Below the floor, you choose: some shops still allow it (a blurry baby photo may be the only one that exists), others refuse to print anything they would not put their name on.
Write the message for a shopper, not a printer
"Effective resolution 118 DPI is below the minimum of 150 DPI" is correct and useless to most people. What a shopper understands is closer to:
Then give them a button that does the first part for them. Most people fix the problem once they know what to click.
Setting it up with Print Preflight
The Print Preflight addon runs these checks live in the designer, as the customer works.
- Install the addon from Veyo → Extensions and activate its license key.
- Open Veyo → Settings → Print readiness. The defaults are a 300 DPI target, a block below 150 DPI, a 3 mm safe margin, 3 mm bleed and 6 pt smallest text.
- Choose the checkout behaviour: Allow, Warn customer (the default) or Block critical errors.
From then on the shopper sees messages such as "This photo may print blurry" or "Too close to the edge" next to the design, each with a one-click fix, plus Fix all for several at once. An overlay shows the trim and safe lines on the product, so "too close to the edge" is something they can see rather than guess.
The same run also checks bleed, safe zones, no-print zones such as a mug's seam or a phone case's camera cut-out, minimum text size, and contrast between the design and the garment colour. Low resolution is simply the one that causes the most reprints.
Help customers fix it without starting over
When the problem is that only part of a photo is needed, cropping helps more than shrinking. The Image Cropper addon lets the shopper crop an image or SVG layer to Original, Free, 1:1, 4:3, 3:4 or 16:9 and zoom up to 4×. The crop is non-destructive: the original is kept for export, so nothing is lost if they change their mind, and the work happens in the browser.
Cropping does not add pixels, so a tight crop of a small photo can still fall below the floor. That is the point of running the resolution check after the crop.
What it does not do
- It does not invent detail. No setting turns a 400-pixel image into a sharp poster; the honest fix is a smaller print or a better file.
- It does not convert colours. Colour management stays with your print workflow.
- It checks against the sizes you enter. If a print area's size is wrong, the DPI is wrong too, so measure the real blank first.
FAQ
Will blocking low-resolution photos cost me sales?
Start with Warn customer and look at your reprints after a month. Many shops find the warning alone fixes most cases, and keep blocking for products where a bad print is expensive.
Does it work on every platform?
Yes. Like every Veyo addon, Preflight works on WooCommerce, OpenCart, PrestaShop and Shopware.
Can staff see the result?
Yes. The same rules apply when staff export the print file, so production sees the same verdict the customer saw.
Next steps
Read the Print Preflight docs for equipment profiles and no-print zones, then try uploading a small photo in the demo to see the warning.