Blog · Print files

Print-ready files for custom products: DPI, bleed and safe zones explained

PUBLISHED: · UPDATED · 6 MIN READ

Most reprints in a personalization shop are not caused by the printer. They come from a file that was never going to print well: a photo stretched to fill a shirt, a name that runs into the seam of a mug, a poster with a white hairline along one edge. All three have names (resolution, safe zone, bleed), and once you know them you can set up your products so the file is right before anyone looks at it.

This post explains the four terms every print shop uses, with numbers you can copy.

1. Resolution: why 300 DPI

DPI (dots per inch) says how many pixels of the image land on each inch of the print. At 300 DPI the eye cannot see individual pixels at reading distance, which is why it is the usual target for anything people hold: shirts, mugs, cards, posters.

The number of pixels you need follows from the physical size:

Print sizePixels at 300 DPIPixels at 150 DPI
10 × 10 cm (chest logo)1181 × 1181591 × 591
20 × 30 cm (A4-ish)2362 × 35431181 × 1772
30 × 40 cm (full front)3543 × 47241772 × 2362

The formula is pixels = centimetres ÷ 2.54 × DPI. A phone photo of 4000 × 3000 pixels is plenty for a chest logo and fine for a full front. A picture saved from a messaging app at 800 pixels wide is not, however good it looks on screen.

150 DPI is a common floor: below it, prints start to look soft. Between 150 and 300 is a judgement call that depends on the product and how close people look at it.

2. Trim: the real edge

The trim line is where the product ends: the edge of a card after cutting, the edge of the printable band on a mug, the outline of a phone case. Your print area should be the size of the trim, measured on the real blank, not on the mockup photo.

Measure the blank, not the picture. Supplier specs are often for a different model or include the handle gap. Put a ruler on the mug you actually print.

3. Bleed: print past the edge

Cutting and pressing are never perfectly aligned. If a design with a coloured background stops exactly at the trim, a 1 mm shift leaves a white sliver. Bleed is extra artwork, usually 3 mm on each side, that extends past the trim and is cut off. It only matters for designs that touch the edge: posters, cards, all-over prints, mug wraps.

A design placed in the middle of a T-shirt does not need bleed. A full-colour poster does.

4. Safe zone: keep text inside

The safe zone is the opposite of bleed: a margin inside the trim, again usually around 3 mm, where nothing important should go. Text and faces that sit right at the edge risk being trimmed, wrapped around a mug's curve or hidden in a seam.

Some products also have areas where nothing should be printed at all: the seam of a sublimation mug, the camera cut-out of a phone case, the zone under a handle. These are often called no-print or exclusion zones.

Putting the four together

ProductResolutionBleedSafe zone
T-shirt, design placed on the chest300 DPI target, 150 minimumNot neededKeep away from collar and seams
Poster or card, full colour300 DPI3 mm3 mm
11oz mug wrap300 DPI3 mm3 mm, plus the seam and handle area
Phone case300 DPIPer the case templateKeep clear of the camera cut-out

File formats your printer will ask for

  • Transparent PNG at 300 DPI, one per printed side. The standard for DTG and DTF.
  • SVG when text and shapes need to stay sharp at any size, or when a cutter or engraver reads vector paths.
  • PDF for print shops and paper products.
  • CMYK TIFF or PDF/X when a commercial printer asks for CMYK. Converting from RGB changes how some colours look, so check a proof.

How Veyo applies this to every order

You set the rules once on the product, and the files follow them:

  • Each print area has its real size in centimetres or inches. The designer shows it at that scale, and exports are made from that size, so a 30 × 40 cm area always produces a 3543 × 4724 pixel PNG.
  • Orders come with a transparent 300 DPI PNG for each side, plus SVG and PDF. CMYK TIFF and PDF/X are available when the server has librsvg, ImageMagick and Ghostscript; without them, PNG, SVG and PDF are made in the browser. See Orders & production.
  • The Print Preflight addon checks resolution, bleed, safe zones, no-print zones, minimum text size and contrast with the garment colour while the customer designs, using defaults of 300 DPI target, 3 mm bleed, 3 mm safe margin and 6 pt smallest text.

The next post covers the most common of these problems in detail: catching low-resolution uploads before checkout.

FAQ

Is 72 DPI enough for print?

No. 72 DPI is a screen convention. What matters is the pixel count for the physical size; use the formula above.

Does a vector file need a DPI?

No. Vectors scale without losing quality. Photos placed inside a vector file still do, so check them separately.

Should I convert to CMYK myself?

Only if your printer asks for it. Most DTG and DTF workflows take RGB PNGs and do their own conversion.

Next steps

Measure one blank you sell, enter its real size as a print area and place a test order. Compare the file's pixel size with the table above.

Try the live demo Read about print files

← All posts